Kagazuru These caps protect the adaptor threads see Figure on page and the sensor membrane see Figure on page from debris and sharp objects. Furthermore, to ensure optimum performance of the HTi, the diameter should not exceed 76 mm 3 in. Seller information garlandequipment Back to home page. This location presents the HTi with the best combination of oil flow, temperature and ease of access.
|Published (Last):||1 July 2010|
|PDF File Size:||17.52 Mb|
|ePub File Size:||4.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
Contact the seller — opens in a new window or tab and request a shipping method to your location. Any visible signs of damage to the shipping packages should be reported to General Electric Canada immediately. See other items More If necessary, use a reducing bushing. Alla procedurer i manualen m?
General Electric Canada shall not be responsible for Part Rev. Suwanee, Georgia, United States. No field calibration required. Seller does not offer returns. For additional information, see the Global Shipping Program terms and conditions — opens in a new window or tab. The two alarm indicators of the door-mounted push-buttons are off. Skip to main content. Screw the sensor manually onto the adaptor. However, the information contained in this manual is subject to change without notice, and does not represent a commitment on the part of General Electric gi.
Interest will be charged to your account 20t1i the purchase date if the balance is not paid in full within 6 months. Do not paint the sensor see Figure on page This item hydrann be shipped through the Global Shipping Program and includes international tracking.
This amount is subject to change until you make payment. Seller assumes all responsibility for this listing. Back to home page. If these four recommended locations cannot be used, contact the General Electric Canada Customer Service see the coordinates at the bottom of page ii to help you determine an acceptable alternative location.
Upon receiving such notice, General Electric Canada may lend telephone support or patches. Hydran Ti Transformer Monitoring System When there are no more air bubbles present in the oil, shut the bleed screw tightly. At this location, the HTi performances are good, rather than excellent. When the HTi is installed horizontally, the terminals must be facing up and located under the sensor. Learn more — opens in new window or tab.
If Products covered by this manual do not meet the above warranties during the applicable Warranty Period, the Buyer shall promptly notify General Electric Canada in writing but not later than 30 days and make the Products available promptly for correction.
The membrane is easily impaired; this would damage the sensor permanently, thus voiding the warranty. Otherwise, armored cables can be used. The low oil flow may affect the gas level readings; however, the lower operating temperatures and ease of access make this location a valid alternative choice.
A new, unused item with absolutely no signs of wear. The HTi requires set-up alarms, temperature, data logging and commissioning for normal use. Connect the other end of the cable to the power source. Jede Abweichung davon k? Watch list is full. Be sure to insert all strands in the terminal; strands that touch two terminals cause problems. This item will ship to United Statesbut the seller has not hyrdan shipping options. Vacuum-resistant gas extraction membrane.
See all condition definitions — opens in a new window or tab. The item may be a factory second or a new, unused item with defects. The Heater indicator yellow, DS8: Please keep all documentation model number, manuals, etc. Please enter a valid ZIP Code. The Hydran Ti is a small on-line early warning transmitter. Its surface must be flat, without cuts or tears. Please read Chapters 2 and 3 before proceeding. Be careful when installing and inserting each wire.
A una distanza massima di 15 m dalla fonte di energia usare un cavo AWG 2. Never apply high voltages to the components of a Hydran i System, even if they are equipped with surge protection devices that could be damaged by Megger tests. Pipe wrench to tighten the brass adaptor onto the valve? TOP Related Posts.
The following details important considerations for the installation of the HTi: 1. Mount the HTi on a full-bore gate valve preferred or a ball valve where there is a good forced or convective oil flow. Install the HTi on a valve with a diameter of 38 mm 1. The recommended location to mount the HTi is on a straight section of the cooler return pipe, and on the discharge side of the pump if present. This location presents the sensor with the best combination of oil flow, operating temperature range and ease of access.
HYDRAN 201TI PDF
It provides continuous monitoring of gas and moisture levels to alert users of developing faults and minimize the risk of unplanned outages. Benefits Small form factor, no moving parts, low maintenance Easy to install on a single valve Condition monitoring for a wide range of transformers with mineral insulating oils or ester based fluids natural and synthetic Real-time composite gas or hydrogen only and moisture in-oil measurement system Automatically alert users of developing fault conditions Supports a wide range of communication methods and protocols Expandable with transformer models capabilities using additional sensors Integrated display and keypad for simplified local user interaction and data visualization 7 year product warranty An example of using external input sensors with Hydran M2-X for transformer models calculations Applications All-in-one solution for important medium size transformers Focuses and prioritizes asset replacement strategy Reduces the risk of process interruption due to power failure Minimizes costly production downtime.
Vur Run the supervisory link cable into the conduit up to the HCi Controller the electrical connections drawings can be found in Appendix A. Full system self test and self-diagnostics. See all viper has no other items for sale. Select a valid country. If necessary, use a reducing bushing. Please read Chapters 2 and 3 before proceeding. Always wrap hyran tape counter to the threads see Figure on page Otherwise, armored cables can be used.
- INTERLANGUAGE THEORY SELINKER PDF
- RAKOVA OBRATNICA PDF
- LINEAR SYSTEMS OPTIMAL AND ROBUST CONTROL ALOK SINHA PDF
- CARMEN CAVALLARO SHEET MUSIC PDF
- BHAGAVATHAM TELUGU PDF
- ACTUATE ROI TO PDF
- EMBEDDED SYSTEMS ARCHITECTURE BY TAMMY NOERGAARD PDF
- IL CACCIATORE DI AQUILONI KHALED HOSSEINI PDF
- DANZAR SU VIDA ROGER GARAUDY PDF