MAKITA 2708 MANUAL PDF

Page 3 Before further use of the tool, a guard or other part that is damaged should be Page 7 The spreader installing location is factory- adjusted. Bolt or screw the Page 10 Bring the ruler underplate flush up against the rail inside, then fasten the hex bolt attaching the underplate very securely Page 14 Use of Miter Gauge Slide the miter gauge into the thick grooves in the table.

Author:Kajijin Kezuru
Country:Andorra
Language:English (Spanish)
Genre:Education
Published (Last):12 April 2016
Pages:436
PDF File Size:20.42 Mb
ePub File Size:20.94 Mb
ISBN:129-6-70245-963-6
Downloads:19989
Price:Free* [*Free Regsitration Required]
Uploader:Sat



Learn the tools applications and limitations, as well as the specific potential hazards peculiar to it. Page 3 Before further use of the tool, a guard or other that it will part that is damaged should be carefully checked ensure oper- ate properly and perform its intended function check for alignment of mov- ing parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.

This tool is equipped w i t h an electric cord hav- ing an equipment-grounding conductor and a grounding plug. Thru-sawing operations are those when the blade cuts complete- ly through the work piece as in ripping or cross cutting. Assemble follows. Grip the outer flange with wrench 22; Page 7: Installing Blade Guard The spreader installing location is factory- adjusted. The bevel is indicated by the arrow pointer. After the desired angle setting i s reached, then lock the lock lever by pressing down firmly t o secure in place.

Page 10 Bring the ruler underplate flush up against Hex bolt -attaching the rail inside, then fasten the hex bolt under d a t e attaching the underplate very securely. Fasten with glue and wood screws as shown. Page 13 Wood Auxiliary Facing Miter Gauge To prevent long board from wobbling, fit the miter gauge with an auxiliary fence board. Fasten with boltdnuts after drilling holes, but fasteners must not protrude from the face board, Featherboard The diagram shown illustrates dimensions for making a typical featherboard.

Page 14 Use of Miter Gauge Slide the miter gauge into the thick grooves in the table. Bring stock flush up against fence and feed gently forward into the blade.

Page 15 Ripping Ripping i s the lengthwise cutting of a board. Use the other hand t o hold the work in position against the rip fence. Page 16 Featherboards A "featherboard" or "fingerboard" is jig made from board cut off a t an angle of degrees. A series of parallel cuts made part way through the board. Board should be straight piece with no knots or cracks see photo.

Featherboards should be used for any operation in which workpiece i s not sawed all the way through and the saw blade guard therefore removed.

Page 17 Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced same time. Use only Makita carbon brushes. Limit mark Lower saw blade as far as possible with the elevating knob; free lock lever and The use of any other accessories or attachments might present risk injury persons.

Page They are attached by clamps to the back of the table and secured with panhead screws. NOTE: Never attempt to move the table saw by gripping these holders.

Page 21 w Chisel tooth combination saw blade For rip and cross-cut work. Most frequently used general carpentry. Page 22 Dado head Part A dado is cutting a rabbet or a wide groove into the workpiece. Outside cutters : 6" diameter, " thick, " Page 23 To install the dado head set, proceed as follows: Turn the tool off and unplug it before installing. Remove the blade guard with the spreader. Install the dado head with the teeth pointing down a t the front of the table. Page 24 NOTE : When widths slightly greater than the above are required, fit the paper washers in between the inside and outside cutters to adjust the width.

Arrange the cutters that the tips of the inside cutters are positioned gullets of the outside cutter. When more than one inside cutter is used, space the tips of the inside cutters equidistantly in relation to one another. Only the Makita dado head set Part No. After dadoing, always replace the blade guard with the spreader back in original posi- i t s tion on the table saw. Page 27 Note: The switch, noise suppressor and other part configurations may differ from country to country.

Page 28 Jan.

ENAMORATE DE TI MISMO WALTER RISO PDF

Makita 2708 Manuals & User Guides

.

ECE R66 PDF

Makita 2708 Instruction Manual

.

GEOHM C PDF

Makita 2708 Saw User Manual

.

Related Articles